|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
HN58C66 Series 8192-word x 8-bit CMOS Electrically Erasable and Programmable CMOS ROM ADE-203-375F (Z) Rev. 6.0 Apr. 12, 1995 Description The Hitachi HN58C66 is a electrically erasable and programmable ROM organized as 8192-word x 8-bit. It realizes high speed, low power consumption, and a high level of reliability, employing advanced MNOS memory technology and CMOS process and circuitry technology. It also has a 32-byte page programming function to make its erase and write operations faster. Features * * * * * * Single 5 V supply On chip latches: address, data, CE, OE, WE Automatic byte write: 10 ms max Automatic page write (32 bytes): 10 ms max High speed: Access time 250 ns max Low power dissipation: 20 mW/MHz typ (active) 2.0 mW typ (standby) Data polling, RDY/Busy Data protection circuit on power on/off Conforms to JEDEC byte-wide standard Reliable CMOS with MNOS cell technology 105 erase/write cycles (in page mode) 10 years data retension Write protection by RES pin * * * * * * * HN58C66 Series Ordering Information Type No HN58C66P-25 HN58C66FP-25 HN58C66T-25 Note: Access Time 250 ns 250 ns 250 ns Package 600-mil 28-pin plastic DIP (DP-28) 28-pin plastic SOP *1 (FP-28D/DA) 32-pin plastic TSOP (TFP-32DA) 1. T is added to the end of the type no. for a SOP of 3.00 mm (max) thickness. 2 HN58C66 Series Pin Arrangement HN58C66P/FP Series RDY/Busy A12 A7 A6 A5 A4 A3 A2 A1 A0 I/O0 I/O1 I/O2 VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 (Top View) 28 27 26 25 24 23 22 21 20 19 18 17 16 15 VCC WE RES A8 A9 A11 OE A10 CE I/O7 I/O6 I/O5 I/O4 I/O3 HN58C66T Series A2 A1 A0 NC I/O0 I/O1 I/O2 VSS I/O3 I/O4 I/O5 I/O6 I/O7 NC CE A10 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A3 A4 A5 A6 A7 A12 NC RDY/Busy VCC NC WE RES A8 A9 A11 OE (Top View) 3 HN58C66 Series Pin Description Pin Name A0 - A12 I/O0 - I/O7 OE CE WE VCC VSS RES NC RDY/Busy Function Address Data input/output Output enable Chip enable Write enable Power supply (+5 V) Ground Reset No connection Ready/Busy Block Diagram I/O0 VCC VSS RES OE CE WE Control Logic and Timing High Voltage Generator I/O Buffer and Input Latch I/O7 RDY/Busy A0 A4 Address Buffer and Latch A5 A12 Y Decoder Y Gating X Decoder Memory Array Data Latch 4 HN58C66 Series Mode Selection Pin Mode Read Standby Write Deselect Write inhibit CE VIL VIH VIL VIL X X Data polling Program reset VIL X OE VIL X *2 WE VIH X VIL VIH VIH X VIH X RDY/Busy High-Z High-Z High-Z to V OL High-Z High-Z RES VH X VH VH X *1 I/O Dout High-Z Din High-Z -- VIH VIH X VIL VIL X VOL High-Z VH VIL Data out (I/O7) High-Z Notes: 1. Refer to the recommended DC operating condition. 2. X = Don't care. Absolute Maximum Ratings Parameter Supply voltage Input voltage *1 *3 *1 Symbol VCC Vin Topr Tstg Value -0.6 to +7.0 -0.5 to +7.0 0 to +70 -55 to +125 *2 Unit V V C C Operating temperature range Storage temperature range Notes: 1. With respect to V SS 2. Vin min = -3.0 V for pulse width 50 ns 3. Including electrical characteristics and data retention Recommended DC Operating Conditions Parameter Supply voltage Input voltage Symbol VCC VIL VIH VH Operating temperature Topr Min 4.5 -0.3 2.2 VCC - 0.5 0 Typ 5.0 -- -- -- -- Max 5.5 0.8 VCC + 1.0 VCC + 1.0 70 Unit V V V V C 5 HN58C66 Series DC Characteristics (Ta = 0 to +70C, VCC = 5 V 10%) Parameter Input leakage current Output leakage current VCC current (standby) VCC current (active) Symbol I LI I LO I CC1 I CC2 Min -- -- -- -- Typ -- -- -- -- Max 2 2 1 8 *1 Unit A A mA mA Test Conditions VCC = 5.5 V, Vin = 5.5 V VCC = 5.5 V, Vout = 5.5/0.4 V CE = VIH, CE = VCC Iout = 0 mA, Duty = 100%, Cycle = 1 s at VCC = 5.5 V Iout = 0 mA, Duty = 100% Cycle = 250 ns at VCC = 5.5 V -- -- 25 mA Input low voltage Input high voltage VIL VIH VH -0.3 *2 2.2 VCC - 0.5 -- 2.4 -- -- -- -- -- 0.8 VCC + 1.0 VCC + 1.0 0.4 -- V V V V V I OL = 2.1 mA I OH = -400 A Output low voltage Output high voltage VOL VOH Notes: 1. I LI on RES = 100 A max. 2. VIL min = -1.0 V for pulse width 50 ns Capacitance (Ta = 25C, f = 1 MHz) Parameter Input capacitance Output capacitance Note: Symbol Cin *1 *1 Min -- -- Typ -- -- Max 6 12 Unit pF pF Test Conditions Vin = 0 V Vout = 0 V Cout 1. This parameter is periodically sampled and not 100% tested. AC Characteristics (Ta = 0 to +70C, VCC = 5 V 10%) Test Conditions * * * * Input pulse levels: 0.4 V to 2.4 V, 0 to V CC (RES pin) Input rise and fall time: 20 ns Output load: 1TTL gate +100 pF Reference levels for measuring timing: 0.8 V, 2.0 V 6 HN58C66 Series Read Cycle Parameter Address to output delay CE to output delay OE to output delay OE (CE) high to output float RES low to output float Data output hold RES to output delay Note: *1 *1 Symbol t ACC t CE t OE t DF t DFR t OH t RR Min -- -- 10 0 0 0 0 Max 250 250 100 90 350 -- 450 Unit ns ns ns ns ns ns ns Test Conditions CE = OE = VIL, WE = VIH OE = VIL, WE = VIH CE = VIL, WE = VIH CE = VIL, WE = VIH CE = OE = VIL, WE = VIH CE = OE = VIL, WE = VIH CE = OE = VIL, WE = VIH 1. t DF , t DFR is defined at which the outputs achieve the open circuit conditions and are no longer driven. Read Timing Waveform Address t ACC CE tCE OE tOE WE High tDF tOH Data Out t RR Data Out Valid t DFR RES 7 HN58C66 Series Write Cycle Parameter Address setup time Address hold time Symbol t AS t AH Min*1 0 150 0 0 0 0 0 0 100 20 200 200 100 0.30 100 -- 120 150 100 1 *3 Typ -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Max -- -- -- -- -- -- -- -- -- -- -- -- -- 30 -- 10 -- -- -- -- *2 Unit ns ns ns ns ns ns ns ns ns ns ns ns ns s s ms ns ns s s Test Conditions CE to write setup time (WE controlled) t CH CE hold time (WE controlled) WE to write setup time (CE controlled) WE hold time (CE controlled) OE to write setup time OE hold time Data setup time Data hold time WE pulse width (WE controlled) CE pulse width (CE controlled) Data latch time Byte load cycle Byte load window Write cycle time Time to device busy Write start time Reset protect time Reset high time t CH t WS t WH t OES t OEH t DS t DH t WP t CW t DL t BLC t BL t WC t DB t DW t RP t RES Notes: 1. Use this device in longer cycle than this value. 2. t WC must be longer than this value unless polling technique or RDY/Busy are used. This device automatically completes the internal write operation within this value. 3. Next read or write operation can be initiated after t DW if polling technique or RDY/Busy are used. 8 HN58C66 Series Byte Write Timing Waveform (1) (WE Controlled) t WC Address t CS CE t AS tWP WE t OES OE t DS Din t DW RDY/Busy High-Z tRP t DB High-Z t DH t OEH t BL t AH t CH tRES RES V CC 9 HN58C66 Series Byte Write Timing Waveform (2) (CE Controlled) Address t WS CE t AS WE t OES OE t DS Din t DW High-Z t RP t DB High-Z t DH t OEH t AH t CW t WH t BL t WC RDY/Busy t RES RES V CC 10 HN58C66 Series Page Write Timing Waveform (1) (WE Controlled) Address A5 to A12 Address A0 to A4 t AS WE t CS CE t AH t WP t DL t CH t BLC t BL t WC t OEH t OES OE t DS Din t DH RDY/Busy High-Z t DB t DW High-Z t RP RES t RES VCC 11 HN58C66 Series Page Write Timing Waveform (2) (CE Controlled) Address A5 to A12 Address A0 to A4 t AS CE t WS WE t AH t CW t DL t WH t BLC t BL t WC t OEH t OES OE t DS Din t DH RDY/Busy High-Z t DB t DW High-Z t RP RES t RES VCC 12 HN58C66 Series Data Polling Timing Waveform Address An An An CE WE t BL OE t CE t OES t OE I/O7 Din X Dout X t WC Dout X t DW Functional Description Automatic Page Write Page-mode write feature allows 1 to 32 bytes of data to be written into the EEPROM in a single write cycle. Following the initial byte cycle, an additional 1 to 31 bytes can be written in the same manner. Each additional byte load cycle must be started within 30 s from the preceding falling edge of WE or CE. When CE or WE is high for 100 s after data input, the EEPROM enters write mode automatically and the input data are written into the EEPROM. Data Polling Data polling allows the status of the EEPROM to be determined. If EEPROM is set to read mode during a write cycle, an inversion of the last byte of data to be loaded outputs from I/O7 to indicate that the EEPROM is performing a write operation. 13 HN58C66 Series RDY/Busy Signal RDY/Busy signal also allows the status of the EEPROM to be determined. The RDY/B usy signal has high impedance except in write cycle and is lowered to V OL after the first write signal. At the end of a write cycle, the RDY/Busy signal changes state to high impedance. RES Signal When RES is low, the EEPROM cannot be read or programmed. Therefore, data can be protected by keeping RES low when VCC is switched. RES should be high during read and programming because it doesn't provide a latch function. VCC Read inhibit Read inhibit RES Program inhibit Program inhibit WE, CE Pin Operation During a write cycle, addresses are latched by the falling edge of WE or CE, and data is latched by the rising edge of WE or CE. Write/Erase Endurance and Data Retention The endurance is 105 cycles in case of the page programming and 3 x 103 cycles in case of byte programming (1% cumulative failure rate). The data retention time is more than 10 years when a device is pageprogrammed less than 104 cycles. 14 HN58C66 Series Data Protection 1. Data Protection against Noise on Control Pins (CE, OE, WE) during Operation During readout or standby, noise on the control pins may act as a trigger and turn the EEPROM to program mode by mistake. To prevent this phenomenon, this device has a noise cancelation function that cuts noise if its width is 20 ns or less in program mode. Be careful not to allow noise of a width of more than 20 ns on the control pins. WE CE 5V 0V 5V OE 0V 20 ns max 15 HN58C66 Series 2. Data Protection at VCC On/Off When V CC is turned on or off, the noise on the control pins generated by external circuits (CPU, etc.) may act as a trigger and turn the EEPROM to program mode by mistake. To prevent this unintentional programming, the EEPROM must be kept in an unprogrammable state by using a CPU reset signal to RES pin. RES pin should be kept at VSS level when V CC is turned on and off. The EEPROM breaks off programming operation when RES becomes low, programming operation doesn't finish correctly in case that RES falls low during programming operation. RES should be kept high for 10 ms after the last data input. VCC RES Program inhibit WE or CE Program inhibit 1 s min 100 s min 10 ms min 16 HN58C66 Series Package Dimensions HN58C66P Series (DP-28) 35.60 36.50 Max Unit: mm 28 15 13.40 14.60 Max 1 1.90 Max 1.20 14 2.54 Min 5.70 Max 15.24 0.51 Min 0.25 - 0.05 0 - 15 + 0.11 2.54 0.25 0.48 0.10 HN58C66FP Series (FP-28D) 18.30 18.75 Max 28 15 8.40 Unit: mm 2.50 Max 1 1.12 Max 14 + 0.08 0.17 - 0.07 11.80 0.30 1.70 0 - 10 1.27 0.40 - 0.05 0.20 M + 0.10 0.20 0.10 1.00 0.20 0.15 17 HN58C66 Series HN58C66FP Series (FP-28DA) 18.00 18.75 Max 28 15 8.40 Unit: mm 1 1.27 Max 14 3.00 Max + 0.08 - 0.07 11.80 0.30 1.70 0 - 10 1.27 0.10 0.40 - 0.05 0.20 0.10 + 0.10 0.17 1.00 0.20 HN58C66T Series (TFP-32DA) 8.00 8.20 Max 32 17 Unit: mm 1 16 0.50 0.20 0.10 0.08 M 14.00 0.20 0.80 0-5 0.50 0.10 0.45 Max 0.17 0.05 1.20 Max 12.40 0.10 18 0.13 0.05 |
Price & Availability of HN58C66SERIES |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |